#Fldigi and cw operation install
#Fldigi and cw operation archive
#Fldigi and cw operation full
#Fldigi and cw operation software

You should create a separate folder for the fldigi CW reader and copy fldigi.exe from the main fldigi installation folder into this separate folder. Click on the Enable check box for Fldigi and set up the location of the fldigi.exe file you are using as a CW reader. Once fldigi has been downloaded (and optionally configured for digital mode operation – see the Digital – Fldigi for Sound Card Modes chapter), it can also be used as a receive-only CW reader (N1MM Logger+ does not support transmitting CW from fldigi).

#Fldigi and cw operation install

Fldigi is not automatically installed with N1MM Logger+ if you want to use it, you must download and install it. The first, Fldigi by W1HKJ, is also one of the digital engines that is supported by the Logger for digital modes. N1MM Logger+ supports three different CW reader programs, or “engines”. The first time you open the CW Reader window, or any time the window is opened with no CW reader engine selected in the setup, the following dialog will be displayed:Īfter clicking on OK in the above window, or at any time thereafter by selecting the Setup menu in the main CW Reader window, the following setup window will be displayed: The CW reader engine cannot be used to transmit CW to transmit CW, you must configure some other method in the Logger (serial or parallel port keying, or a Winkeyer, for example).

Setup DX, DXpedition, and General Purpose Contests.

Windows – Table of Contents View (long).

Call History and Reverse Call History Lookup.

#Fldigi and cw operation archive

Archive Files (1/2021) – N1MM on WindowsXP.

That works, but for now I'm putting this to rest as 'not working'. I'll post results again if I stumble on some settings combination SSB mode, but it's just not clicking for CW on TX. I like fldigi andįlrig for the FT-991A and they work great for any tone modulated Sadly, it's just not working for me on CW.

#Fldigi and cw operation full

Released (or maybe not for full QSK, I'm not sure about that). Stop while the TX text is being sent and resume when the PTT is One would think that with DTR keying, the waterfall should Showing TX tones on the waterfall when it should be toggling theĭTR?. Insisting on sending audio tones even if I disable CAT PTT inįavour of DTR PTT which I think is wrong. Installed and the standard port isn't being used by anything else

'standard' comport for CAT or Separate PTT even though they are For one, neither flrig nor fldigi offer the If you elected to use theĢnd COM port for PTT then that port will not be visible toĭave, I appreciate your advice on this topic but haven't Thanks to everyone who responded on this topic, 73, Hugo, ve3ktn.įlrig should be using CAT for PTT. I'll post results again if I stumble on some settings combination that works, but for now I'm putting this to rest as 'not working'. I like fldigi and flrig for the FT-991A and they work great for any tone modulated SSB mode, but it's just not clicking for CW on TX.

One would think that with DTR keying, the waterfall should stop while the TX text is being sent and resume when the PTT is released (or maybe not for full QSK, I'm not sure about that). Why should fldigi be showing TX tones on the waterfall when it should be toggling the DTR?. As I mentioned before, fldigi is insisting on sending audio tones even if I disable CAT PTT in favour of DTR PTT which I think is wrong. MMSSTV, Gpredict so I know it's installed correctly).

#Fldigi and cw operation software

For one, neither flrig nor fldigi offer the 'standard' comport for CAT or Separate PTT even though they are installed and the standard port isn't being used by anything else (it is visible to other software e.g. If you elected to use the 2nd COM port for PTT then that port will not be visible to fldigi.ĭave Dave, I appreciate your advice on this topic but haven't progressed at all.